The most balancing part of world is jungle
Lions vs Sunwolves live stream Tour de France 2017 live stream Sligo vs Meath Live Stream Donegal vs Longford live stream Dublin vs Laois live stream Mayo vs Derry live stream
View Articleyhnb yjuhn b
Horn vs Pacquiao live stream Pacquiao vs Horn live stream Wimbledon 2017 live stream Tour de France 2017 live stream Sligo vs Meath Live Stream Donegal vs Longford live stream Dublin vs Laois live...
View ArticlePercentage
Guys, I'm having a brain fart and for the life of me can't get an LCD to display the value of a word variable as a percentage. The word variable is CH1_PWM and ranges from 0 to 4095 I tried this Code:...
View ArticleHow does the code get transferred?
Hi All, I do not understand a variable labeled as Wdata and some how it gets transferred out of the PIC to the device being controlled. I can understand if you are using a command such as Hserout but...
View ArticleMax7221
Hi, I'm using MAX7221 display driver, I know how to set it up. I need to send serially a 16 bit number to the display, but I found that I need to decode the number into digits digit 1, digit 2... etc....
View ArticleHB100 radar module
Hello all, I try to find something about that MW radar module on PB forum but no success. I have already done the backpack module from limpkin, all works fine. I can read frequencies on scope but how...
View ArticleTime limit while waiting for input ?
I'm using a 16F628A to control a DC motor, also using hall effect sensors as limit switches. All working fine however I'm concerned that if one of the hall sensors should fail the motor will keep...
View ArticleI got this message so ...
hello I got this message so i make a post ! sorry if it is not in the good area .. Francois Hello, welcome to our forum. It looks like you have registered but you have not yet posted and messages. Our...
View ArticleUsing MCLR pin at Input
I am using a 12F683 and having no luck in disabling the MCLR pin (pin 4 bit 3) so that I can use it as an input. In the PicBasic program, I put ANSEL = 0 to set all the pins to digital and CMCON0 = 7...
View ArticleOnewire.pbp sample program -- high readings
This program -- http://melabs.com/samples/PBP-mixed/onewire.htm works fine but at room temperature I'm getting -- 178 C 350 F I am using a probe with a DS18B20 sensor, perhaps that's it but I can't...
View ArticleByte to integer ?
Is there any way I can get the integer value from a byte/word or vice versa with PBP ? I need to monitor a word and compare it with a preset integer value. I'm using the DS18B20 and it's the...
View ArticleADC on 12F683
I am not able to get the ADC on a 12F683 to work. The values it reports fluctuate seemingly randomly. I have two 4.7K resistors attached in series between +5V and GND. A wire from Pin 4 (bit 3) is...
View ArticleMicroCode Studio not displaying full microcontroller list
Something I have done in the last week has resulted in MicroCode Studio only displaying 16F628A and 18F25K20 in its Microcontroller list. I Have PBP 3.1 installed and activated and MicroCode Studio...
View ArticleOnce own world
UFC 213 live stream Waterford vs Kilkenny live stream Dublin vs Tipperary live stream
View Article@ device ?????
Hi! I have seen Config and have never seen "@ device PIC16F628A,HS_OSC,BOD_ON,MCLR_ON,PWRT_ON" Is this valid? How do I change it for a 20MHZ crystal? Thanks, Ed
View ArticleIs it possible to feed PBP variable data into ASM code fragment?
I need to control built in HPWM of PIC16F1825 with PBP. The problem is, that HPWM statement on each execution, stops and restarts HPWM module, which is not desirable. If I issue ASM statement, I can...
View ArticleFIBA Basketball World Cup 2017 Canada vs Italy takes place today
Canada vs Italy Live Stream
View ArticleCANBUS Stuff
Are there any other CANBUS hopefuls on here or any more recent examples than in the archives. There is not much CANBUS stuff and a lot is very old. I'm using a 18F2680 and MCP2551 transceiver... ISO...
View ArticleLCDOUT -- lose the zero ?
Can't figure out how to do this -- mynumber = byte mynumber = 120 LCDOUT $FE,1,DEC mynumber also tried -- LCDOUT $FE,1,#mynumber Problem is that whenever I lower the number below 100 (I have 2 switches...
View Article