Hello,
Can I have some guidance, I have written the code below to drive a set of LEDs attached to a SN74HC595, I am using a PIC16F1825 to drive the SN74HC595.
3 LEDs are attached to the PIC16F1825 to provide feedback that the code is cycling as expected. These all function correctly.
The connection between the PIC and the shift register is as below:
PIC16F1825 SN74HC595
SDO PIN 3 RA4 PIN 14 SER
SDI PIN 9 RA5 Floating Not Connected
SCK PIN 10 RC0 PIN 11 SRCLK
Latch out PIN 11 RA2 PIN 12 RCLK
Common ground and 5V power supply is provided to both the PIC and shift register. no resistors or capacitors are connected between the PIC and the shift register.
LEDs are connected to the 9 outputs of the shift register.
The LEDs attached to the shift register stay lit, but do not cycle off, or make any of the expected patterns.
What am I doing wrong? Thank you in advance.
Can I have some guidance, I have written the code below to drive a set of LEDs attached to a SN74HC595, I am using a PIC16F1825 to drive the SN74HC595.
3 LEDs are attached to the PIC16F1825 to provide feedback that the code is cycling as expected. These all function correctly.
The connection between the PIC and the shift register is as below:
PIC16F1825 SN74HC595
SDO PIN 3 RA4 PIN 14 SER
SDI PIN 9 RA5 Floating Not Connected
SCK PIN 10 RC0 PIN 11 SRCLK
Latch out PIN 11 RA2 PIN 12 RCLK
Common ground and 5V power supply is provided to both the PIC and shift register. no resistors or capacitors are connected between the PIC and the shift register.
LEDs are connected to the 9 outputs of the shift register.
The LEDs attached to the shift register stay lit, but do not cycle off, or make any of the expected patterns.
What am I doing wrong? Thank you in advance.
Code:
TxData var BYTE
define OSC 4
OSCCON = %01101010
HC_Data var PORTA.4 'SDO
HC_Clk var PORTC.0 'SCK
HC_latch var PORTA.2 'Digital output
LED_YELLOW var PORTA.1
LED_GREEN var PORTC.3
LED_RED var PORTA.0
TRISA = 0 'all digital outputs
PORTA = 0 'make all pins low
ANSELA = 0
TRISC = %00000010 'all digital outputs except port 1
PORTC = 0 'make all pins low
ANSELC = 0
APFCON0 = %01000000 'set SPI pin alternative
SSP1STAT = %00000000
SSP1CON1 = %01100010
SSP1CON3 = %00010000
txdata = 0 'SPI output byte
pause 200 'prove LED function
LED_YEllow = 1
LED_Green = 1
LED_red = 1
pause 200
LED_YEllow = 0
LED_Green = 0
LED_red = 0
Main: 'set up sequence of signals for output
LED_Yellow = 1
TxData = %10101010
Gosub Send_Data
TXDATA = %00000000
Gosub Send_Data
TxData = %10000000
Gosub Send_Data
TxData = %01000000
Gosub Send_Data
TxData = %00100000
Gosub Send_Data
LED_Yellow = 0
LED_gREEN = 1
TxData = %00010000
Gosub Send_Data
TxData = %00001000
Gosub Send_Data
TxData = %00000100
Gosub Send_Data
TXDATA = %00000010
Gosub Send_Data
TXDATA = %00000001
Gosub Send_Data
LED_GREEN = 0
goto main
end
Send_Data :
SSP1CON1.5 = 0
SSP1CON1.5 = 1
toggle LED_RED
PAUSEUS 10
SSP1BUF = TXDATA
PAUSEUS 10
HC_Latch=1
pauseus 5
HC_Latch=0
pause 750
return